文章摘要
张山寅,杨俊锋,芦跃峰,等.铝/钢薄板无铆连接接头成形过程及形貌控制[J].精密成形工程,2023,15(5):44-53.
ZHANG Shan-yin,YANG Jun-feng,LU Yue-feng,et al.Forming Process and Morphology Control of Mechanical Clinch Joint of Steel/Aluminum Sheet[J].Journal of Netshape Forming Engineering,2023,15(5):44-53.
铝/钢薄板无铆连接接头成形过程及形貌控制
Forming Process and Morphology Control of Mechanical Clinch Joint of Steel/Aluminum Sheet
  
DOI:10.3969/j.issn.1674-6457.2023.05.006
中文关键词: 无铆连接  成形控制  应力分析  互锁结构
英文关键词: mechanical clinch  forming control  stress analysis  interlocking structure
基金项目:中央引导地方科技发展资金(226Z1809G)
作者单位
张山寅 燕山大学 机械工程学院河北 秦皇岛 066004 
杨俊锋 燕山大学 机械工程学院河北 秦皇岛 066004 
芦跃峰 中国重型机械研究院股份公司西安 710018 
余超 燕山大学 机械工程学院河北 秦皇岛 066004 
肖宏 燕山大学 机械工程学院河北 秦皇岛 066004 
仇平 燕山大学 机械工程学院河北 秦皇岛 066004 
摘要点击次数: 1309
全文下载次数: 682
中文摘要:
      目的 研究铝/钢薄板无铆连接过程中接头形貌的影响因素。方法 采用有限元模拟方法分析了铝/钢薄板在平底模具下接头形貌的成形过程。结合变形区域的金属流动情况,解释了互锁结构的形成机理,并分析了不同工艺参数对接头形貌的影响。结果 接头互锁结构主要是依靠铝板填充钢板的凹陷部位而形成的,抑制钢板与模具接触一侧的金属流动有助于接头底部和侧壁的钢板拉薄,进而形成内部凹陷,促进互锁结构的形成。摩擦因数对接头形貌参数影响较大,增大摩擦因数可显著提高接头的互锁量。结论 冲头半径、冲头圆角、凹模深度以及摩擦因数对颈厚值和互锁量均有显著影响。通过控制这些影响因素,可以得到良好的接头。此外,接头的失效形式以铝板颈厚较薄处的剪断失效为主,因此对于采用铝上钢下的无铆连接,保证颈厚值相对于互锁量更加重要。
英文摘要:
      The work aims to study the affecting factors on morphology of joint of steel/aluminum sheet in mechanical clinch. The forming process of joint morphology of steel/aluminum sheet in flat bottom die was simulated by finite element method. The formation mechanism of interlocking structure was explained based on the metal flow in each region, and the effect of different process parameters on morphology of joint was analyzed. The interlocking structure of the joint was mainly formed by filling the concave part of the steel sheet inside the joint with aluminum sheet. Inhibiting the metal flow on the side of the steel sheet in contact with the die was conductive to thinning the steel sheet at the bottom and the side wall of the joint, thus forming the internal concave and promoting the formation of the interlocking structure. The friction coefficient had a great effect on the morphology parameters of joint, and increasing the friction coefficient could significantly improve the interlocking quantity of joint. The punch radius, punch fillet, die depth and friction coefficient all have a significant effect on the neck thickness and the interlocking quantity. By controlling these affecting factors, a good joint can be obtained. In addition, the failure mode of the joint is mainly the shear failure at the thinner neck of the aluminum sheet. Therefore, for the mechanical clinch with the aluminum sheet at top and the steel sheet at bottom, it is more important to ensure the neck thickness than the interlocking quantity.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第13925553位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号