文章摘要
黄少东,张志明,庞丹,等.带底深孔空心件热成形工艺改进分析[J].精密成形工程,2014,6(1):27-31.
HUANG Shao-dong,ZHANG Zhi-ming,PANG Dan,et al.Improvement Analysis of Thermoforming Technology for Bottomed Hollow Part with Deep Hole[J].Journal of Netshape Forming Engineering,2014,6(1):27-31.
带底深孔空心件热成形工艺改进分析
Improvement Analysis of Thermoforming Technology for Bottomed Hollow Part with Deep Hole
投稿时间:2013-11-10  修订日期:2013-11-10
DOI:10.3969/j.issn.1674-6457.2014.01.005
中文关键词: 带底深孔空心件  热成形  冲孔  拔伸  润滑  冲头  模具寿命
英文关键词: bottomed hollow part with deep hole  thermoforming  punching  drawing  lubrication  punch  mould life
基金项目:国防基础科研重点项目( A1020110004)
作者单位
黄少东 西南技术工程研究所, 重庆 400039 
张志明 西南技术工程研究所, 重庆 400039 
庞丹 辽沈工业集团有限公司, 沈阳 110045 
孙锋 辽沈工业集团有限公司, 沈阳 110045 
闫峰 辽沈工业集团有限公司, 沈阳 110045 
赵志翔 西南技术工程研究所, 重庆 400039 
赵祖德 西南技术工程研究所, 重庆 400039 
摘要点击次数: 10949
全文下载次数: 7574
中文摘要:
      目的 研究带底深孔空心件热成形工艺现状与改进措施。 方法 介绍分析了目前国内外所采用的新工艺、模具结构,新型润滑剂、强制润滑方法,新型模具材料、制造工艺及应用情况。 结果 采用压型、预冲孔、冲孔、拔伸工艺及模口导向的效果良好,通过高压将润滑剂从冲头内部流向冲孔冲头前端,可实现冲孔强制润滑,模具材料可用 3 Cr3Mo3 VNb,4 Cr2MoVNi,3 Cr3Mo3W2 V 等,并采用表面强化等工艺。 结论 应用表明,上述改进措施可降低壁厚差,改进产品质量,并减小摩擦,降低成形力,比传统材料及工艺显著提高了模具寿命。 最后指出了还需进一步解决的问题。
英文摘要:
      Objective The current status and improvement of thermoforming technology for bottomed hollow part with deep hole have been introduced in some papers and patents. Methods New technology and mould structure, new lubricants and forced lubrication, new mould materials as well as manufacturing processes and applications were introduced and analyzed in this paper. Results The results showed that the technology of pressing, pre-pierce, pierce, drawing and installing guiding assembly had good effect on the die orifice. Forced lubrication could be realized by communicating pressurized lubricant to the exterior of a piercing punch. Mould materials of 3Cr3Mo3VNb, 4Cr2MoVNi, 3Cr3Mo3W2V etc. and surface strengthening techniques could be utilized. Conclusion Applications showed that the measures could be used to reduce wall thickness variation, improve product quality, reduce friction and forming load, and improve the mould life compared with the conventional materials and processes. Some problems remaining to be solved were introduced at the end.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12860342位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号