文章摘要
邓劲松,陈辛波,魏宪波,等.冲压件成形仿真及其预成形模具方案设计[J].精密成形工程,2014,6(1):21-26.
DENG Jin-song,CHEN Xin-bo,WEI Xian-bo,et al.Sheet Panel Forming Simulation and Scheme Design of Pre -forming Die[J].Journal of Netshape Forming Engineering,2014,6(1):21-26.
冲压件成形仿真及其预成形模具方案设计
Sheet Panel Forming Simulation and Scheme Design of Pre -forming Die
投稿时间:2013-08-10  修订日期:2013-11-16
DOI:10.3969/j.issn.1674-6457.2014.01.004
中文关键词: 预成形  氮气弹簧  模具结构
英文关键词: pre-forming  gas spring  die structure
基金项目:
作者单位
邓劲松 同济大学, 上海 201804 
陈辛波 同济大学, 上海 201804 
魏宪波 同济大学, 上海 201804 
丁华 吉利汽车研究院, 杭州 311228 
冯擎峰 吉利汽车研究院, 杭州 311228 
摘要点击次数: 13979
全文下载次数: 5489
中文摘要:
      目的 预测高强度钢板的冲压成形性。 方法 对使用高强度材料的左前地板 2 号横梁进行了数字仿真模拟,设计了一种提高板料抗破裂性能的带氮气弹簧的预成形模具。 先根据仿真结果,在采用调整工艺参数的常规手段未果的情况下,分析了破裂原因,再根据成形模拟软件的使用要求,对氮气弹簧的技术特性进行了处理,保证能代入成形软件。 结果 再次成形模拟证明,采用氮气弹簧的预成形模具,能改善模具受力状态,使成形件不致破裂。 结论 预成形模具结构有助于改善特定形状冲压件的成形性。
英文摘要:
      Objective To predict the forming ability of high-strength steel. Methods Formability of panel C / MBR_FRT_FLOOR_No. 2_LH, which adopted HSS, was analyzed in this paper. Pre-forming die with gas spring was designed to improve the anti -split ability of the blank. Firstly, according to the simulation result, the split reasons were analyzed, under the condition that the changing of process parameters by general method was not effective. Secondly, in order to use the parameter of gas spring, the technical characteristic of which was specially treated based on the using requirement of simulation software. Results The second simulation result showed that the stress state of die could be improved after adopting pre -forming die structure, and that cracks problems could be avoided. Conclusion The results also showed that pre -forming die structure is helpful to improve the forming ability of parts with specific shape.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第13490768位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号