文章摘要
耿佩,龚小涛,陈文静,等.Zr–2.5Nb合金热变形行为研究[J].精密成形工程,2022,14(6):65-70.
GENG Pei,GONG Xiao-tao,CHEN Wen-jing,et al.Hot Deformation Behavior of Zr-2.5Nb[J].Journal of Netshape Forming Engineering,2022,14(6):65-70.
Zr–2.5Nb合金热变形行为研究
Hot Deformation Behavior of Zr-2.5Nb
  
DOI:10.3969/j.issn.1674-6457.2022.06.009
中文关键词: Zr–2.5Nb  温度  应变速率  激活能
英文关键词: Zr-2.5Nb  temperature  strain rate  activation energy
基金项目:西安航空职业技术学院2019年度科研计划(19XHZK–004)
作者单位
耿佩 西安航空职业技术学院西安 710089 
龚小涛 西安航空职业技术学院西安 710089 
陈文静 西安航空职业技术学院西安 710089 
周超 西安航空职业技术学院西安 710089 
马晶 西安航空职业技术学院西安 710089 
摘要点击次数: 1138
全文下载次数: 741
中文摘要:
      目的 研究Zr–2.5Nb合金热压缩后的应力–应变关系和合金变形激活能。方法 对Zr–2.5Nb进行高温压缩试验,分析变形条件(温度和应变速率)对该合金热变形行为的影响,研究高温压缩过程中Zr–2.5Nb合金的显微组织变化,并基于Arrhenius公式分析其变形激活能。结果 在低温、高应变速率条件下,Zr–2.5Nb合金应力由峰值快速降低直至达到稳态;在高温和低应变速率下,该合金的应力–应变曲线呈现动态再结晶特征,合金平均变形激活能为468.962 kJ/mol,硬化指数为5.41。结论 在850~1 000 ℃下进行不同应变速率的热压缩变形时,高温低应变速率有利于Zr–2.5Nb动态再结晶的发生;同一温度条件下,低应变速率时合金变形激活能较小,有利于Zr–2.5Nb合金发生塑性变形。
英文摘要:
      Based on hot compression experiments, the paper aims to analyze the high temperature stress-strain relationship and the deformation activation energy of Zr-2.5Nb alloy. The effect of deformation temperature and strain rate on the rheological behavior of Zr-2.5Nb alloy was investigated by high temperature compression test, and the deformation activation energy was analyzed based on Arrhenius relation. At low temperature and high strain rate, the stress-strain curves of Zr-2.5Nb alloy showed obvious dynamic recrystallization characteristics, while at high temperature and low strain rate, the stress-strain curves of Zr-2.5Nb alloy decreased rapidly from peak to steady state, the average activation energy of deformation was 468.962 kJ/mol, and the hardening exponent was 5.41. Under 850-1 000 ℃ hot compression deformation condition, low strain rate is favorable to the plastic deformation of Zr-2.5Nb alloy. High temperature and low strain rate is favorable to the dynamic recrystallization of Zr-2.5Nb.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12289785位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号