文章摘要
张健辉,纪志军,冯新,等.ZTA15铸造钛合金高周疲劳性能研究[J].精密成形工程,2022,14(6):28-35.
ZHANG Jian-hui,JI Zhi-jun,FENG Xin,et al.High-cycle Fatigue Properties of ZTA15 Cast Titanium Alloy[J].Journal of Netshape Forming Engineering,2022,14(6):28-35.
ZTA15铸造钛合金高周疲劳性能研究
High-cycle Fatigue Properties of ZTA15 Cast Titanium Alloy
  
DOI:10.3969/j.issn.1674-6457.2022.06.004
中文关键词: ZTA15铸造钛合金  高周疲劳性能  显微组织  疲劳失效机理
英文关键词: ZTA15 cast titanium  high-cycle fatigue properties  microstructure  fatigue failure mechanism
基金项目:国家重点研发计划(2020YFB2008300)
作者单位
张健辉 中国航发北京航空材料研究院北京 100095
北京航空材料研究院股份有限公司北京 100094
北京市先进钛合金精密成型工程技术研究中心北京 100084 
纪志军 中国航发北京航空材料研究院北京 100095
北京航空材料研究院股份有限公司北京 100094
北京市先进钛合金精密成型工程技术研究中心北京 100084 
冯新 中国航发北京航空材料研究院北京 100095
北京航空材料研究院股份有限公司北京 100094
北京市先进钛合金精密成型工程技术研究中心北京 100084 
陈冬梅 沈阳飞机设计研究所沈阳 110035 
杨国娟 沈阳飞机工业集团有限公司沈阳 110034 
摘要点击次数: 1467
全文下载次数: 747
中文摘要:
      目的 研究ZTA15铸造钛合金的高周疲劳性能及其疲劳断裂微观机理。方法 测试ZTA15铸造钛合金的室温轴向拉伸高周疲劳性能,并对合金的金相组织和断口形貌进行观察与分析。结果 随着应力比的提高,ZTA15铸造钛合金的疲劳强度相应提高,疲劳寿命也相应延长。应力比为−1、0.06、0.5时,相应ZTA15铸造钛合金的中值疲劳强度分别为341.5、512.5、643 MPa。疲劳断口形貌显示,疲劳裂纹多萌生于试棒的表面和次表面,裂纹萌生区呈类解理断裂特征。裂纹扩展区可以观察到明显的疲劳辉纹、扩展台阶和二次裂纹等典型特征。结论 疲劳失效机理和疲劳性能差异与合金的显微组织有一定的关系。应力比对疲劳性能的影响主要作用于疲劳裂纹的萌生和扩展阶段。
英文摘要:
      This paper aims to study the high-cycle fatigue properties and fatigue fracture mechanism of ZTA15 cast titanium alloy. The axial tensile high-cycle fatigue properties of ZTA15 cast titanium alloy under room temperature are tested, and the metallographic structures and fracture morphologies of the alloy are observed and analyzed. With the increase of stress ratio, the fatigue strength and fatigue life of ZTA15 cast titanium alloy increase. When the stress ratio is −1, 0.06 and 0.5 respectively, the median fatigue strength of the corresponding ZTA15 cast titanium alloy is 341.5, 512.5, 643 MPa respectively. The fatigue fracture morphologies show that most of the fatigue cracks originate on the surface and sub surface of the specimen, and most of the cracks originate in the form of cleavage fracture. Obvious fatigue striations, propagation steps and secondary crack can be observed in the crack propagation. The fatigue failure mechanism and the difference of fatigue properties are related to the microstructure of the alloy. The effect of stress ratio on fatigue performance mainly acts on the initiation and propagation stages of fatigue cracks.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12241681位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号