文章摘要
高勃兴,邹德坤,谢红飙,等.铝/钢轧制复合有限元二次开发模拟与实验研究[J].精密成形工程,2021,13(6):56-63.
GAO Bo-xing,ZOU De-kun,XIE Hong-biao,et al.Simulation and Experimental Study on Finite Element Secondary Development of Aluminum/Steel Rolling Composite[J].Journal of Netshape Forming Engineering,2021,13(6):56-63.
铝/钢轧制复合有限元二次开发模拟与实验研究
Simulation and Experimental Study on Finite Element Secondary Development of Aluminum/Steel Rolling Composite
投稿时间:2021-07-06  
DOI:10.3969/j.issn.1674-6457.2021.06.007
中文关键词: 铝/钢复合板  变形协调性  ABAQUS  机理分析  结合强度
英文关键词: aluminum/steel composite plate  deformation compatibility  ABAQUS  mechanism analysis  bonding strength
基金项目:国家重点研发计划(2018YFA0707302);河北省钢铁联合基金(E2019203466)
作者单位
高勃兴 燕山大学 国家冷轧板带装备及工艺工程技术研究中心河北 秦皇岛 066004 
邹德坤 燕山大学 国家冷轧板带装备及工艺工程技术研究中心河北 秦皇岛 066004 
谢红飙 燕山大学 国家冷轧板带装备及工艺工程技术研究中心河北 秦皇岛 066004 
肖宏 燕山大学 国家冷轧板带装备及工艺工程技术研究中心河北 秦皇岛 066004 
朱宇飞 燕山大学 国家冷轧板带装备及工艺工程技术研究中心河北 秦皇岛 066004 
摘要点击次数: 1397
全文下载次数: 564
中文摘要:
      目的 针对铝/钢两种金属性能差异大,轧制复合存在严重的变形不协调及结合强度低的问题,研究轧辊同径与异径及单辊驱动对复合板协调变形及结合强度的影响。方法 通过有限元二次开发进行模拟建模,并结合同步和异步轧制实验分析板翘曲机理。结果 与铝板接触的轧辊作为主驱动辊可使板变形更协调且结合强度更高,变形翘曲度为0.048,结合强度为34.2 MPa。结论 采用接触铝侧轧辊单侧驱动,双金属界面实现复合的位置更靠近轧辊出口,复合后的双金属界面间的剪应力和所受弯矩较小,制备的铝/钢复合板变形协调性更好,且结合强度更高。
英文摘要:
      The work aims to study the influence of the same diameter and different diameter of the roll and the single roll drive on the coordinated deformation and the bonding strength of the composite plate, so as to solve the large difference in properties between aluminum and steel, the serious deformation incoordination and low bonding strength in rolling compound. Through secondary development of finite element modeling, the plate warpage mechanism was analyzed in combination with synchronous and asynchronous rolling experiment. The roller in contact with the aluminum plate as the main driving roller could make the plate deformation more coordinated. The bonding strength was higher. The deformation warpage was 0.048 and the bonding strength was 34.2 MPa. When the roll contacting the aluminum side is driven, the position of bimetal interface is closer to the exit of the roll. Moreover, the shear stress and bending moment between the composited bimetal interfaces are smaller. Aluminum/steel composite plate prepared by this method has better deformation coordination and higher bonding strength.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12073462位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号