文章摘要
张宏亮,吴冰洁,杨龙龙,等.纳米单晶铜磨料磨损行为的分子动力学研究[J].精密成形工程,2020,12(2):98-103.
ZHANG Hong-liang,WU Bing-jie,YANG Long-long,et al.Abrasive and Wear of Nano Single Crystal Copper: a Molecular Dynamics Simulation[J].Journal of Netshape Forming Engineering,2020,12(2):98-103.
纳米单晶铜磨料磨损行为的分子动力学研究
Abrasive and Wear of Nano Single Crystal Copper: a Molecular Dynamics Simulation
投稿时间:2020-01-08  修订日期:2020-03-10
DOI:10.3969/j.issn.1674-6457.2020.02.016
中文关键词: 磨料磨损  工艺参数  表面形貌  内部缺陷
英文关键词: abrasive wear  process parameters  surface morphology  internal defects
基金项目:
作者单位
张宏亮 1. 中国核动力研究设计院成都 610041 
吴冰洁 1. 中国核动力研究设计院成都 610041 
杨龙龙 2. 西安交通大学西安 710049 
张亚楠 2. 西安交通大学西安 710049 
孙琨 2. 西安交通大学西安 710049 
方亮 2. 西安交通大学西安 710049 
摘要点击次数: 2912
全文下载次数: 2015
中文摘要:
      目的 探究在不同参数下纳米单晶铜的磨料磨损行为。方法 通过构建纳米单晶铜的摩擦磨损模型,对磨粒施加不同的滑动速度、滑动距离以及外载荷,研究在不同滑动速度、滑动距离、外载荷下纳米单晶铜磨料磨损行为。结果 随着磨料与单晶铜基体之间滑动速度的增加(50, 100, 200 m/s),基体内部缺陷减少;随着滑动距离的增大(4, 8, 16 nm),基体被去除的原子增多且主要集中在磨料前端;随着外载荷的增大(40, 80 nN),基体内部缺陷的最大深度增大,且表面无定形原子增多。结论 在不同的滑动速度、滑动距离、外载荷等参数下,主要包括基体内部缺陷和表层无定形原子的纳米单晶铜磨料磨损行为有明显差异。
英文摘要:
      The paper aims to study the effects of different parameters on the abrasive wear of nano single crystal copper. By constructing the friction and wear model of nano single crystal copper, different sliding speed, different sliding distance and different external load were applied to the abrasive particles to study the abrasive wear behavior of nano single crystal copper under different sliding speed, sliding distance and external load. It was found that with the increase of the sliding speed (50, 100, 200 m/s) between the abrasive and the single crystal copper substrate, the internal defects of the copper substrate were reduced. The atoms removed by the substrate increased with the increase of sliding distance (4, 8, 16 nm). Moreover, the atoms mainly concentrated on the front end of the abrasive. As the external load increased (40, 80 nN), both the maximum depth of defects in the matrix and the number of amorphous atoms on the surface increased. Under different sliding speed, sliding distance and external load, there are obvious differences in the abrasive wear behavior of nano single crystal copper, mainly including the internal defects of the matrix and the amorphous atoms on the surface.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第13210347位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号