文章摘要
谭观华,王善林,吴鸣,等.电子束焊接K418高温合金裂纹的影响及组织与性能研究[J].精密成形工程,2019,11(5):103-108.
TAN Guan-hua,WANG Shan-lin,WU Ming,et al.Effect of Cracks in Electron Beam Welding of K418 Superalloy and Its Microstructure and Properties[J].Journal of Netshape Forming Engineering,2019,11(5):103-108.
电子束焊接K418高温合金裂纹的影响及组织与性能研究
Effect of Cracks in Electron Beam Welding of K418 Superalloy and Its Microstructure and Properties
投稿时间:2019-07-20  修订日期:2019-09-10
DOI:10.3969/j.issn.1674-6457.2019.05.015
中文关键词: 高温合金  电子束焊接  显微组织  裂纹
英文关键词: superalloy  electron beam welding  microstructure  crack
基金项目:国家自然科学基金(51461031);轻合金加工科学与技术国防重点学科实验室基金(gf201501005)
作者单位
谭观华 南昌航空大学 江西省航空构件成形与连接重点实验室南昌 330036 
王善林 南昌航空大学 江西省航空构件成形与连接重点实验室南昌 330036 
吴鸣 南昌航空大学 江西省航空构件成形与连接重点实验室南昌 330036 
孙文君 南昌航空大学 江西省航空构件成形与连接重点实验室南昌 330036 
陈玉华 南昌航空大学 江西省航空构件成形与连接重点实验室南昌 330036 
柯黎明 南昌航空大学 江西省航空构件成形与连接重点实验室南昌 330036 
摘要点击次数: 2756
全文下载次数: 1998
中文摘要:
      目的 探究工艺参数对K418高温合金焊接裂纹的影响,减少焊接过程中裂纹的产生。方法 采用真空电子束对2 mm的薄板K418高温合金进行焊接试验,通过改变工艺参数来调控焊接裂纹,使用光学显微镜对焊缝显微组织进行观察,使用显微硬度计对试样进行硬度测量,万能拉伸计对接头进行拉伸试验,使用扫描电镜对断口进行观察。结果 在焊接束流为24 mA,焊接速度为600 mm/min时,扫描波形为O形,频率为500 Hz时,焊接接头表面未发现裂纹。通过拉伸试验发现断裂位置为母材,其断口为典型脆性解离断裂。结论 采用合适的工艺参数可以减少或消除焊接接头表面裂纹的形成。
英文摘要:
      The paper aims to study the effect of process parameters on weld crack of K418 superalloy and reduce the formation of cracks during welding. The welding of 2 mm thin plate K418 superalloy was carried out by vacuum electron beam. The welding crack was controlled by changing the process parameters. The microstructure of the weld was observed with optical and scanning electron microscopy. The hardness of the sample was measured with microhardness tester. The tensile test was carried out on the joint with universal tensile tester. The fracture was observed with scanning electron microscope. The results showed that when the welding beam current was 24 mA and the welding speed was 600 mm/min, the scanning waveform was O-shaped. When the frequency was 500 Hz, no crack was found on the surface of the welding joint. Through the tensile test, the fracture position was found to be the base material, and the fracture was a typical brittle dissociation fracture. The formation of surface cracks in the welding joint can be reduced or eliminated under suitable process parameters.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12070482位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号