文章摘要
张春红,颜长林,王彦伟,等.200 ℃等温时效下SAC305/Co-5%P焊点的界面组织及断裂模式演变[J].精密成形工程,2019,11(2):41-44.
ZHANG Chun-hong,YAN Chang-lin,WANG Yan-wei,et al.Interfacial Microstructure and Fracture Pattern of SAC305/Co-5%P Solder Joint during Isothermal Aging at 200 ℃[J].Journal of Netshape Forming Engineering,2019,11(2):41-44.
200 ℃等温时效下SAC305/Co-5%P焊点的界面组织及断裂模式演变
Interfacial Microstructure and Fracture Pattern of SAC305/Co-5%P Solder Joint during Isothermal Aging at 200 ℃
投稿时间:2019-01-05  修订日期:2019-03-10
DOI:10.3969/j.issn.1674-6457.2019.02.007
中文关键词: 等温时效  金属间化合物  断口形貌
英文关键词: isothermal aging  intermetallic compounds  fracture morphology
基金项目:国家自然科学基金(61804018);重庆市科委项目(cstc2016jcyjA0226);重庆市教委项目(KJ1600912);重庆市巴南区项目(2017TJ08)
作者单位
张春红 1. 特种焊接材料与技术重庆市高校工程研究中心 重庆理工大学重庆 400054 
颜长林 2. 重庆长征重工有限责任公司重庆 400083 
王彦伟 2. 重庆长征重工有限责任公司重庆 400083 
牟喜军 2. 重庆长征重工有限责任公司重庆 400083 
彭诗琴 2. 重庆长征重工有限责任公司重庆 400083 
王渝 2. 重庆长征重工有限责任公司重庆 400083 
谢代芳 1. 特种焊接材料与技术重庆市高校工程研究中心 重庆理工大学重庆 400054 
摘要点击次数: 3526
全文下载次数: 2880
中文摘要:
      目的 研究BGA封装的SAC305/Co-5%P焊点在200 ℃等温时效下的界面反应。方法 制备SAC305/Co-5%P的BGA焊点,200 ℃等温时效0, 200, 400, 600, 1000 h,采用场发射扫描电镜(配EDS)观察不同时效时间下SAC305/Co-5%P焊点界面的IMC形貌与断口特征,采用焊点接合强度测试仪测试相应的剪切强度变化。结果 时效1000 h时,在钎料/CoSn3的IMC层界面处生成(Cu, Co)6Sn5,界面CoSn3的IMC之间的通道得到填充,界面形貌变得平整。随着时效时间的增加,焊点的剪切强度先增后降,位于Sn层断口的断裂模式由韧性断裂向韧脆混合型断裂转变。结论 随着时效时间的增加,界面IMC层厚度不断增加,界面IMC形貌发生改变。
英文摘要:
      The paper aims to research the interfacial reaction of SAC305/Co-5%P solder joints that encapsulated by BGA during isothermal aging at 200 ℃. SAC305/Co-5%P BGA solder joints were prepared by isothermal aging for 0, 200, 400, 600, 1000 h at 200 ℃. The interface IMC morphology and fracture characteristics of SAC305/Co-5%P solder joints were observed by SEM (equip EDS), and the shear strength changes were measured by solder joint strength tester. (Cu, Co)6Sn5 was formed at the interface of solder/CoSn3 IMC layer during isothermal aging for 1000 h; the channel between the interface CoSn3 IMC was filled; and the interface morphology became smooth. With the increase of aging time, the shear strength of solder joints increased first and then decreased. The fracture pattern changed from ductile fracture in Sn layer to ductile-brittle mixed fracture. With the increase of aging time, the thickness of IMC layer increases and the morphology of IMC changes.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12244908位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号