文章摘要
曹民业,刘光辉,汪金保,等.一种挖掘机斗齿多向精密成形工艺研究[J].精密成形工程,2019,11(1):30-35.
CAO Min-ye,LIU Guang-hui,WANG Jin-bao,et al.Research on Multi-Directional Precision Forming Process of Excavator Bucket Teeth[J].Journal of Netshape Forming Engineering,2019,11(1):30-35.
一种挖掘机斗齿多向精密成形工艺研究
Research on Multi-Directional Precision Forming Process of Excavator Bucket Teeth
投稿时间:2018-11-27  修订日期:2019-01-10
DOI:10.3969/j.issn.1674-6457.2019.01.005
中文关键词: 挖掘机斗齿  多向精密成形  数值模拟  工艺试验
英文关键词: excavator bucket tooth  multi-direction precision forming  numerical simulation  process text
基金项目:
作者单位
曹民业 郑州机械研究所郑州 450001 
刘光辉 郑州机械研究所郑州 450001 
汪金保 郑州机械研究所郑州 450001 
李春洋 郑州机械研究所郑州 450001 
许午阳 郑州机械研究所郑州 450001 
刘华 郑州机械研究所郑州 450001 
摘要点击次数: 4077
全文下载次数: 2705
中文摘要:
      目的 研究挖掘机斗齿多向精密锻造成形工艺。方法 根据挖掘机斗齿的结构特点,设计一种多向精密成形工艺方案。使用Deform-3D有限元分析软件对提出的工艺方案进行模拟,分析锻造过程中的载荷-行程曲线和金属流动规律,最后设计模具并进行工艺试验。结果 通过数值模拟与工艺试验,获得了成形过程中的工艺参数,揭示了挖掘机斗齿多向精密成形过程的变形规律。结论 提出的多向精密成形工艺方案成形挖掘机斗齿没有超出模具的许用应力范围,工艺试验获得的锻件充填饱满,无锻造缺陷。
英文摘要:
      The paper aims to research multi-direction precision forming technology of excavator bucket teeth. A multi-direction precision forming technology based on structural characteristics of the excavator bucket teeth. The proposed forming process was numerically simulated through Deform-3D. In this process, the load-stroke curve, the metal flow law, etc were analyzed. Finally, the mold was designed for process test. Through numerical simulation and process test, the process parameters in the forming process were obtained. The deformation law of the multi-directional precision forming process of the excavator teeth was revealed. The multi-directional precision forming process proposed in this paper does not exceed the allowable stress range of the mold, and the forgings obtained in the process test are full and have no forging defects.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12073702位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号