文章摘要
禹杰,林有希,范宜鹏.芳纶纤维复合材料高速钻削刀具磨损机理研究[J].精密成形工程,2018,10(6):123-127.
YU Jie,LIN You-xi,FAN Yi-peng.Tool Wear Mechanism of High Speed Drilling for Aramid Fiber Reinforced Plastic[J].Journal of Netshape Forming Engineering,2018,10(6):123-127.
芳纶纤维复合材料高速钻削刀具磨损机理研究
Tool Wear Mechanism of High Speed Drilling for Aramid Fiber Reinforced Plastic
投稿时间:2018-07-30  修订日期:2018-11-10
DOI:10.3969/j.issn.1674-6457.2018.06.021
中文关键词: 芳纶纤维复合材料  高速钻削  失效形式  磨损机理
英文关键词: aramid fiber reinforced plastic  high speed drilling  failure mode  wear mechanism
基金项目:国家自然科学基金(51375094)
作者单位
禹杰 福州大学 a. 机电工程实践中心福州 350116 
林有希 福州大学 b. 机械工程及自动化学院福州 350116 
范宜鹏 福州大学 b. 机械工程及自动化学院福州 350116 
摘要点击次数: 3610
全文下载次数: 2635
中文摘要:
      目的 研究高转速条件下芳纶纤维复合材料(AFRP)钻削过程中刀具的摩擦学行为。方法 采用TiAlN涂层超细微碳化钨晶粒麻花钻对芳纶纤维复合材料进行高速钻削试验。首先,研究整个寿命阶段刀具后刀面磨损规律。其次,观察分析刀具磨损处的微观形貌,深入研究刀具的失效形式与磨损机理。结果 刀具磨损可分为3个阶段,分别为初期磨合阶段、稳定磨损阶段、急剧磨损阶段,各阶段磨损速率各不相同,稳定磨损阶段最小,急剧磨损阶段最大。涂层刀具的失效形式为涂层与基体材料剥落以及后刀面磨损,磨粒磨损为主要的磨损形式,同时伴随着不同程度的粘结磨损和氧化磨损,使后刀面形成诸多凹坑和划痕。结论 丰富了复合材料高速钻削中的刀具磨损机理,并为钻削刀具的选用及性能优化提供理论与试验依据。
英文摘要:
      The paper aims to study tribological behaviors of cutter when drilling the aramid fiber reinforced plastic (AFRP) at high speed. The TiAlN coated drill of ultra-fine tungsten carbide grain was adopted for high-speed drilling test of aramid fiber reinforced plastic. Firstly, the wear law of the tool flank face during the whole life stage was studied. Secondly, the microscopic morphology of the tool wear was observed and analysed. Then, the failure mode and wear mechanism of the tool were studied furtherly. The tool wear could be divided into three stages, including initial wear stage, stable wear stage and sharp wear stage. The wear rate varied from stage to stage, while the stable wear stage was the smallest, and the sharp wear stage was the largest. The failure mode of the coated tool was coating flaking and flank wear. The abrasive wear was the main form of wear, accompanied with different degrees of adhesive wear and oxidative wear, which caused many pits and scratches on flank face. This research enriches the tool wear mechanism in high speed drilling of composite materials. And it provides theoretical and experimental basis for the selection and performance optimization of drilling tools.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12409456位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号