文章摘要
侯政良,王柱飞,张雪冬,等.热处理工艺对34CrNiMo6钢性能的影响研究[J].精密成形工程,2018,10(6):38-42.
HOU Zheng-liang,WANG Zhu-fei,ZHANG Xue-dong,et al.Effects of Heat Treatment on Performance of 34CrNiMo6 Steel[J].Journal of Netshape Forming Engineering,2018,10(6):38-42.
热处理工艺对34CrNiMo6钢性能的影响研究
Effects of Heat Treatment on Performance of 34CrNiMo6 Steel
投稿时间:2018-10-09  修订日期:2018-11-10
DOI:10.3969/j.issn.1674-6457.2018.06.007
中文关键词: 热处理  结构钢  组织  性能  工艺
英文关键词: heat treatment  structural steel  microstructure  performance  technology
基金项目:总装预研基金(41423040323)
作者单位
侯政良 1. 北方通用动力集团有限公司山西 大同 037036 
王柱飞 1. 北方通用动力集团有限公司山西 大同 037036 
张雪冬 1. 北方通用动力集团有限公司山西 大同 037036 
郭巨寿 1. 北方通用动力集团有限公司山西 大同 037036 
康凤 2. 西南技术工程研究所重庆 400039 
摘要点击次数: 3731
全文下载次数: 2718
中文摘要:
      目的 提高34CrNiMo6钢构件抗拉强度、屈服强度以及伸长率的匹配程度,进而提高合金的冲击韧性和疲劳性能。方法 通过热处理试验,研究不同工艺对材料组织和性能的影响。采用预先热处理(正火+高温回火)→调质热处理(淬火+回火)的工艺,研究不同淬火和回火温度对试样组织及力学性能的影响。结果 随着淬火温度的升高,试样的强度有所增加,伸长率差别不大,在淬火温度为900 ℃时冲击韧性有所下降。随着回火温度的升高,强度明显降低,但伸长率逐渐升高,冲击韧性则稍有提升。结论 通过试验确定了材料的热处理工艺:850 ℃淬火+580 ℃回火。在该调质工艺下,材料的强度和塑性得到了合理的匹配。
英文摘要:
      The paper aims to improve the matching of tensile strength, yield strength and elongation of 34CrNiMo6 steel, and improve the impact toughness and fatigue properties of alloy. Heat treatment test was carried out to research effects of different processes on microstructure and mechanical properties of samples. Pre-heat treatment (normalizing and high-temperature tempering) + quenched-tempered heat treatment (hardening and tempering) were used to study effects of different quenching and tempering temperature on microstructure and mechanical properties of samples. With the increase of quenching temperature, the strength of the sample increased, but there was little difference in the variation of elongation. The impact toughness decreased at 900 ℃. As the tempering temperature risen, the strength decreased obviously, but the elongation increased gradually and the impact toughness increased slightly. Through the test, the heat treatment process of materials was determined to be quenched at 850 ℃ and tempered at 580 ℃. With this tempering process, the strength and plasticity of the material were properly matched.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12298235位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号