文章摘要
吉喆,高二庆,沈承金,等.钛合金锥形压痕约束因子和代表应变的确定[J].精密成形工程,2018,10(6):10-16.
JI Zhe,GAO Er-qing,SHEN Cheng-jin,et al.Determination of Constraint Factor and Representative Strain Introduced by Sharp Indentation on Titanium Alloy[J].Journal of Netshape Forming Engineering,2018,10(6):10-16.
钛合金锥形压痕约束因子和代表应变的确定
Determination of Constraint Factor and Representative Strain Introduced by Sharp Indentation on Titanium Alloy
投稿时间:2018-09-26  修订日期:2018-11-10
DOI:10.3969/j.issn.1674-6457.2018.06.002
中文关键词: 钛合金  压痕测试  有限元分析  约束因子  代表应变
英文关键词: titanium alloy  indentation test  finite element analysis  constraint factor  representative strain
基金项目:国家自然科学基金(51505481)
作者单位
吉喆 1. 中国矿业大学江苏 徐州 221116 
高二庆 2. 徐州巴特工程机械股份有限公司江苏 徐州 221004 
沈承金 1. 中国矿业大学江苏 徐州 221116 
宋庆雷 2. 徐州巴特工程机械股份有限公司江苏 徐州 221004 
徐杰 1. 中国矿业大学江苏 徐州 221116 
郭涛 1. 中国矿业大学江苏 徐州 221116 
摘要点击次数: 3536
全文下载次数: 2645
中文摘要:
      目的 研究钛合金性能参数与约束因子和代表应变的关系。方法 对不同性能参数条件下压痕变形过程进行有限元仿真,根据模拟结果建立约束因子和代表应变与材料性能间的定量关系。结果 发现钛合金屈服强度与压痕硬度之间存在线性关系。约束因子随着弹性模量的增加而增加,代表应变随着弹性模量的增加而减小。当弹性模量固定不变时,约束因子随屈服强度线性减小,代表应变固定不变。在材料性能范围内,使用代表应变求解的代表应力,与通过压痕硬度和约束因子求解的代表应力两者误差小于±3%。结论 材料性能不同,约束因子和代表应变的值也会变化,这两个参数并不存在统一的值。
英文摘要:
      The paper aims to study the relationship between mechanical properties, constraint factor and representative strain of titanium alloy. Finite element simulations of indentation deformation process were performed on titanium alloy with different performance parameters. The quantitative relation between constraint factor and representative as well as material property was established based on the result of simulation. The result shows that there was a linear relationship between yield stress and indentation hardness of titanium alloy. Constraint factors increased with the increase of elastic modulus, while representative strains decreased with the increase of elastic modulus. When elastic modulus was fixed, constraint factors decreased linearly with yield strength and representative strains remained unchanged. In the range of material properties, the error of representative stresses calculated by representative strain and constraint factor was less than ±3%. Therefore, constraint factor and representative strain depend on the material properly and there is no universal value for the two parameters.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12082152位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号