文章摘要
熊英超,夏琴香,叶福源,等.多工位级进模冲裁工序模具磨损行为的数值分析及寿命预测[J].精密成形工程,2017,9(3):89-93.
XIONG Ying-chao,XIA Qin-xiang,YE Fu-yuan,et al.Numerical Analysis and Life Prediction of Die Wear Behavior in Multi-Position Progressive Die Blanking[J].Journal of Netshape Forming Engineering,2017,9(3):89-93.
多工位级进模冲裁工序模具磨损行为的数值分析及寿命预测
Numerical Analysis and Life Prediction of Die Wear Behavior in Multi-Position Progressive Die Blanking
投稿时间:2017-04-21  修订日期:2017-05-10
DOI:10.3969/j.issn.1674-6457.2017.03.017
中文关键词: 多工位级进模  Archard理论  数值分析  模具磨损  模具寿命
英文关键词: multi-position progressive die  archard theory  numerical analysis  die wearing  die life
基金项目:广东省佛山市顺德区产学研合作项目(2014CXY18)
作者单位
熊英超 华南理工大学 机械与汽车工程学院广州 510641 
夏琴香 华南理工大学 机械与汽车工程学院广州 510641 
叶福源 广东科龙模具有限公司广东 佛山 528303 
陈志平 广东科龙模具有限公司广东 佛山 528303 
摘要点击次数: 2878
全文下载次数: 4099
中文摘要:
      目的 针对多工位级进模连续冲裁所带来的模具磨损问题。方法 基于Archard磨损理论,以凸模为研究对象,对其磨损行为进行有限元数值模拟,通过设计冲裁间隙、冲裁速度、模具硬度等工艺参数之间的正交试验,获得各工艺参数对模具磨损的变化规律及最佳工艺组合;采用磨损累计法,对模具修模前的凸模圆角半径和使用寿命进行预测。结果 冲裁模具磨损区域主要分布在模具圆角处,并得到单次最大模具磨损量为4.30×10-7 mm;得到磨钝后的圆角半径为0.3 mm,冲裁极限次数为27万次。结论 采用该分析方法能较好地预测磨损,并为模具的保养修复提供一定的参考价值。
英文摘要:
      The paper aims to solve the problem of die wear caused by continuous blanking of multi-position progressive die. Based on the Archard wearing theory, a terrace die was researched to have numerical modeling on finite element of wearing. The variation rule and optimal process combination of influences of process parameters on die wearing were obtained through orthogonal test among design of blanking clearance, blanking speed, and die hardness. Furthermore, the fillet radius and the service life of the punch die before repairing were predicted by the method of wearing accumulation. The wearing area of blanking die was mainly distributed in the fillet corner of the die, and the maximum wearing amount in the single stamping was 4.30×10-7 mm. And the radius of the fillet corner was 0.3 mm after blunting, and the limit time of the blanking was 270 thousand. The method can predict the wear well and provide some reference value for the maintenance of the die.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第8908492位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号