文章摘要
李向博,马俊林,薛克敏,等.基于ANSYS Workbench 液压支架顶梁多工况结构优化与静力分析[J].精密成形工程,2015,7(2):60-65.
LI Xiang-bo,MA Jun-lin,XUE Ke-min,et al.Structural Optimization of Multiple Operating Condition and Static Analysis of Top-beam of the Hydraulic Support Based on ANSYS Workbench[J].Journal of Netshape Forming Engineering,2015,7(2):60-65.
基于ANSYS Workbench 液压支架顶梁多工况结构优化与静力分析
Structural Optimization of Multiple Operating Condition and Static Analysis of Top-beam of the Hydraulic Support Based on ANSYS Workbench
投稿时间:2015-01-09  修订日期:2015-03-10
DOI:10.3969/j.issn.1674-6457.2015.02.011
中文关键词: ANSYS Workbench  多目标优化设计  轻量化  敏感性  静力学分析
英文关键词: ANSYS Workbench  multi-objective optimized design  lightweight  sensitivity  static analysis
基金项目:
作者单位
李向博 合肥工业大学材料科学与工程学院, 合肥230009 
马俊林 合肥工业大学材料科学与工程学院, 合肥230009 
薛克敏 合肥工业大学材料科学与工程学院, 合肥230009 
杜勇 合肥工业大学材料科学与工程学院, 合肥230009 
徐杰 合肥工业大学材料科学与工程学院, 合肥230009 
摘要点击次数: 4026
全文下载次数: 3694
中文摘要:
      目的 优化尺寸参数,最大程度减小质量,实现顶梁的轻量化。方法 利用ANSYS Work-bench 对液压支架顶梁进行了参数化建模,对其多种工况进行了多目标优化设计。结果 研究结果表明,优化结果符合设计要求,顶梁在3 种工况满足刚度和强度的同时,质量分别减轻了10. 4%,9. 59%,4. 26%,实现了轻量化。在此基础上,对顶梁的多工况进行静力学分析,检验了优化的效果。结论 顶梁结构的最大等效应力减小,应力分布更加合理。
英文摘要:
      The aim of this study was to optimize the size parameters, reduce the quality as much as possible to realize the lightweight of beams. The top beam of hydraulic support was parameterized by modeling using ANSYS Workbench,and multi-operated optimization designwas conducted for its various operating conditions. The results showed that the optimization results met the design requirements, and lightweight was achieved. The top beam in the three different conditions met both the stiffness and strength requirements, and the mass was reduced by 10. 4%,9. 59%, 4. 26%,respectively. Based on the above study, static analysis was carried out for the top beam under the multiple operation conditions, to inspect the optimization effects. The maximum equivalent stress of the top beam structure tended to become smaller,and the stress distribution became more reasonable.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12073887位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号