文章摘要
鄢光旭,王新云,金俊松,等.凸缘的翻孔镦粗过程研究[J].精密成形工程,2014,6(2):6-11.
YAN Guang-xu,WANG Xin-yun,JIN Jun-song,et al.Flanging-upsetting Process of Flange[J].Journal of Netshape Forming Engineering,2014,6(2):6-11.
凸缘的翻孔镦粗过程研究
Flanging-upsetting Process of Flange
投稿时间:2014-01-06  修订日期:2014-03-01
DOI:10.3969/j.issn.1674-6457.2014.02.002
中文关键词: 不变薄凸缘  有限元分析  凸缘镦粗  镦粗比
英文关键词: flange without thinning  finite element analysis  flange upsetting  upsetting ratio
基金项目:国家自然科学基金(51205144)
作者单位
鄢光旭 华中科技大学 材料成形与模具技术国家重点实验室, 武汉 430074 
王新云 华中科技大学 材料成形与模具技术国家重点实验室, 武汉 430074 
金俊松 华中科技大学 材料成形与模具技术国家重点实验室, 武汉 430074 
邓磊 华中科技大学 材料成形与模具技术国家重点实验室, 武汉 430074 
摘要点击次数: 7884
全文下载次数: 4651
中文摘要:
      目的 研究不变薄凸缘的翻孔件的翻孔镦粗成形过程。方法采用有限元模拟软件ABAQUS,对不变薄凸缘的翻孔件的翻孔镦粗过程建立了平面二维对称的有限元模型,并进行了有限元计算分析;完成了模具设计,并在1000kN的伺服压力机上进行了实验。结果 当凹模圆角为1.2mm,凸凹模间隙在0.80~0.86之间时,单次镦粗可以获得与初始坯料厚度一致的凸缘。结论 凹模圆角大小及凸凹模间隙大小对不变薄凸缘翻孔凸缘质量有着重要的影响,并最终影响凸缘的镦粗过程。
英文摘要:
      Objective To investigate the flanging-upsetting process of flange. Methods Finite simulation software ABAQUS was adopted to establish the 2D planar symmetrical model to simulate the process. Die was designed for the experiments which were conducted on the 1000 kN servo press. Results A flange with the thickness equal to the initial blank was obtained after one time upsetting when the female die radius was 1. 2 mm and the clearance between the punch and die was in the range of 0. 80 ~ 0. 86. Conclusion The female die radius and the clearance between the punch and die obviously affected the quality of flange, which affected the upsetting process.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12071488位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号