文章摘要
丁祖宏,李纪龙,乔硕,等.汽车弯臂锻造工艺改进数值模拟及实验研究[J].精密成形工程,2013,5(5):24-28.
DING Zu-hong,LI Ji-long,QIAO Shuo,et al.Numerical Simulation and Experimental Study for Forging Process of Automotive Curved Arm[J].Journal of Netshape Forming Engineering,2013,5(5):24-28.
汽车弯臂锻造工艺改进数值模拟及实验研究
Numerical Simulation and Experimental Study for Forging Process of Automotive Curved Arm
投稿时间:2013-04-18  修订日期:2013-08-01
DOI:10.3969/j.issn.1674-6457.2013.05.006
中文关键词: 汽车弯臂  辊锻  数值模拟  金属流动规律
英文关键词: automobile curved arm  roll forging  numerical simulation  metal flowing law
基金项目:
作者单位
丁祖宏 合肥汽车锻件有限责任公司, 合肥 230009 
李纪龙 合肥工业大学 材料科学与工程学院, 合肥 230009 
乔硕 合肥工业大学 材料科学与工程学院, 合肥 230009 
薛克敏 合肥工业大学 材料科学与工程学院, 合肥 230009 
摘要点击次数: 4260
全文下载次数: 3452
中文摘要:
      采用理论分析、计算机数值模拟和实验研究相结合的方法对汽车弯臂锻造工艺进行了优化设计研究。 用 Deform 软件对弯臂成形工艺中的辊锻、弯曲和模锻工艺进行了精确的数值模拟,得到了金属流动、应力应变分布规律,并通过对辊锻工艺的改进来改变金属的分布,减少飞边尺寸,达到提高材料利用率,降低成本的目的。 利用工厂现有设备对弯臂成形工艺进行了实验研究,实验结果表明,改进后的锻件充填饱满,飞边较小,材料利用率得到了提高,验证了该改进工艺的可行性和优越性。
英文摘要:
      The theoretical analysis,computer numerical simulation and experimental research are used to study the forging process of automobile curved arm. The Deform software is used to accurately simulate the processes of roll forging,bending and forging and the metal flowing law in these processes and the distribution of stress and strain. The distribution of the metal can be changed and the flash size can be reduced by the improvement of the roll forging process to improve the material utilization. The experimental study of the forging process is carried out with the existing equipment. The experimental results show that the improved forging has smaller flash with higher material utilization,which verifies the feasibility and advantage of the improved process.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12076587位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号