文章摘要
贾尚武,王召林,刘松,等.三辊斜轧空心减径的辊形设计及实验验证[J].精密成形工程,2013,5(5):18-23,28.
JIA Shang-wu,WANG Zhao-lin,LIU Song,et al.Roll Profile Design and Experiment on Three Roll Cross Rolling of Hollow Diameter Reduction[J].Journal of Netshape Forming Engineering,2013,5(5):18-23,28.
三辊斜轧空心减径的辊形设计及实验验证
Roll Profile Design and Experiment on Three Roll Cross Rolling of Hollow Diameter Reduction
投稿时间:2013-06-21  修订日期:2013-08-01
DOI:10.3969/j.issn.1674-6457.2013.05.005
中文关键词: 三辊斜轧  空心减径  辊形设计  ANSYS 有限元
英文关键词: three roll cross rolling  hollow diameter reduction  roll profile design  ANSYS finite element
基金项目:
作者单位
贾尚武 中国重型机械研究院股份公司, 西安 710000 
王召林 山西王坪煤电有限责任公司, 山西 朔州 036000 
刘松 中国重型机械研究院股份公司, 西安 710000 
帅全志 山西省太重煤机煤矿装备成套有限公司, 太原 030000 
摘要点击次数: 4821
全文下载次数: 4002
中文摘要:
      以三辊斜轧空心减径过程中辊形对轧制过程的影响规律为研究对象,对无缝钢管三辊斜轧空心减径过程进行分析研究,建立了辊型的数学模型。 利用有限元软件分析辊形曲线对成形过程的影响,并在某三辊实验轧机上进行实验分析,将实验结果与有限元模拟结果进行对比和分析。 结果表明,当减径量小于10 mm 时,入口锥角为 2 . 5 o 的辊型对应的轧件在接近均整变形区金属流动十分平缓和均匀,轧件前端面也从三角形截面逐步变为圆截面;当减径量在 14 mm 左右,采用入口锥角为 3 . 5 o 的辊型时轧件的质量较好。
英文摘要:
      This paper studies effects of roll shape on rolling process in three roll rolling hollow diameter reduction, and analyzes the reducing process of the seamless hollow three roll cross rolling, establishes a mathematical model of roll. Using finite element analysis software roll shape curve effect on the forming process is analyzed and experiments are performed on an experimental three roll mill. Finally, the experimental results and finite element simulation results are compared and analyzed. The paper gives following conclusions: when the reduced diameter is less than 10 mm, the metal flow near the entire deformation zone for the rolling part with inlet cone angle of 2. 5o of roll is very gentle and uniform, the front surface of the rolling part is also gradually turned from triangular cross -section to round ones, and when the reducing amount is 14 mm or so, the quality is better by using the entrance cone angle of 3. 5o of roll rolling.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第13211326位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号