文章摘要
张翔,李萍,王晓溪,等.ECAPT过程中载荷变化规律的数值模拟[J].精密成形工程,2010,2(5):6-9.
ZHANG Xiang,LI Ping,WANG Xiao-xi,et al.The FEM Numerical Simulation of Loads in ECAPT[J].Journal of Netshape Forming Engineering,2010,2(5):6-9.
ECAPT过程中载荷变化规律的数值模拟
The FEM Numerical Simulation of Loads in ECAPT
投稿时间:2010-05-31  修订日期:2010-09-10
DOI:
中文关键词: 大塑性变形  等径角挤压  挤扭  等径角挤扭  数值模拟
英文关键词: severe plastic deformation  equal channel angular pressing  twist extrusion  equal channel angular pressing and torsion  numerical simulation
基金项目:国家自然科学基金(50875072);霍英东教育基金会(121053);安徽省优秀青年科技基金(10040606Y21)
作者单位
张翔 合肥工业大学 材料科学与工程学院 合肥 230009 
李萍 合肥工业大学 材料科学与工程学院 合肥 230009 
王晓溪 合肥工业大学 材料科学与工程学院 合肥 230009 
薛克敏 合肥工业大学 材料科学与工程学院 合肥 230009 
吴战立 合肥工业大学 材料科学与工程学院 合肥 230009 
摘要点击次数: 3529
全文下载次数: 2698
中文摘要:
      为了掌握纯铝在ECAPT过程中的力学变化规律,利用刚塑性有限元技术对纯铝1100的ECAPT变形行为进行数值模拟,重点分析了载荷在挤压过程中的变化规律及产生变化的原因。结果表明:ECAPT过程大致分为载荷骤升、2次小幅度升高和载荷下降4个阶段;载荷峰值随着摩擦因数的增大迅速增大,应采取有效的润滑措施减小摩擦从而降低载荷峰值,提高模具寿命;随着摩擦因数的增大,载荷在达到各阶段峰值后下降趋势越来越明显。
英文摘要:
      In order to master the variation regularity of mechanics in the ECAPT process, the rigid-plastic FEM has been used in the numerical simulation of ECAPT of aluminum 1100. The load variation and the reasons were mainly investigated. The results show that ECAPT of aluminum 1100 can be classified into four phases in the process: the load increases fast, the load increases slowly two times, the load declines. Peak value of load will increase swiftly with the friction coefficient increasing. An effective lubricating measure should be adopted to reduce the peak value and prolong the mould life. With friction coefficient increasing the load will decline obviously when it reaches the peak value.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12081569位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号