文章摘要
舒大禹,肖远伦,胡传凯,等.Mg-10Gd-2Y-0.6Zr合金热压缩变形及其微观组织研究[J].精密成形工程,2010,2(4):1-6.
SHU Da-yu,XIAO Yuan-lun,HU Chuan-kai,et al.Study on Hot Compression Deformation of Mg-10Gd-2Y-0.6Zr Alloy and its Microstructure[J].Journal of Netshape Forming Engineering,2010,2(4):1-6.
Mg-10Gd-2Y-0.6Zr合金热压缩变形及其微观组织研究
Study on Hot Compression Deformation of Mg-10Gd-2Y-0.6Zr Alloy and its Microstructure
投稿时间:2010-05-17  修订日期:2010-07-10
DOI:
中文关键词: Mg-10Gd-2Y-0.6Zr合金  热压缩变形  变形激活能  本构方程  微观组织
英文关键词: Mg-10Gd-2Y-0.6Zr alloy  hot compression deformation  deformation activation energy  constitutive equation  microstructure
基金项目:
作者单位
舒大禹 1.中国兵器工业第五九研究所, 重庆 4000392.国防科技工业精密塑性成形技术研究应用中心, 重庆 400039 
肖远伦 1.中国兵器工业第五九研究所, 重庆 4000392.国防科技工业精密塑性成形技术研究应用中心, 重庆 400039 
胡传凯 1.中国兵器工业第五九研究所, 重庆 4000392.国防科技工业精密塑性成形技术研究应用中心, 重庆 400039 
康凤 1.中国兵器工业第五九研究所, 重庆 4000392.国防科技工业精密塑性成形技术研究应用中心, 重庆 400039 
黄树海 1.中国兵器工业第五九研究所, 重庆 4000392.国防科技工业精密塑性成形技术研究应用中心, 重庆 400039 
宁海青 1.中国兵器工业第五九研究所, 重庆 4000392.国防科技工业精密塑性成形技术研究应用中心, 重庆 400039 
赵祖德 1.中国兵器工业第五九研究所, 重庆 4000392.国防科技工业精密塑性成形技术研究应用中心, 重庆 400039 
摘要点击次数: 3203
全文下载次数: 2827
中文摘要:
      采用GLEEBLE-1500热模拟机对Mg-10Gd-2Y-0.6Zr合金在温度为350~450 ℃,变形速率为0.001~0.5 s-1,最大变形程度为50%的条件下,进行了恒应变速率高温压缩模拟试验研究,分析了合金高温变形时流变应力与应变速率及变形温度之间的关系以及组织变化。结果表明:合金的稳态流变应力随应变速率的增大而增大,随温度的升高而降低;在给定的变形条件下,计算出合金的变形激活能和应力指数分别为223 kJ/mol和6.9,建立了合金高温变形的本构方程;根据试验分析,合金变形温度为400 ℃,变形速率为0.5 s-1,或变形温度为450 ℃,变形速率为0.1 s-1下进行热压缩,可以得到组织结构均匀和热塑性加工良好的匹配。
英文摘要:
      By GLEEBLE-1500 thermal simulator, high temperature compression simulation experiments of Mg-10Gd-2Y-0.6Zr alloy with constant strain rate were studied, which were under the conditions of 350~450 ℃, 0.001~0.5 s-1 and maximal deformation of 50%. The microstructure transformation, the relationships between rheological stress and strain rate and temperature, were analyzed under hot deformation. The results showed that the steady-state rheological stress increased with strain rate increasing or deformation temperature decreasing. In given deformation condition, the deformation activation energy and stress index were 223 kJ /mol and 6.9 separately. And the constitutive equation of Mg-10Gd-2Y-0.6Zr alloy was established. A match of good thermoplastic processing and uniform microstructure could be obtained under hot compression with the strain rate of 0.5 s-1 at 400 ℃, or with the strain rate of 0.1 s-1 at 450 ℃.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第12071159位访问者    渝ICP备15012534号-6

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

>    

渝公网安备 50010702501719号